Replace Lock in UPVC Door

If you have a Upvc door lock that isn't working correctly, you need to call a professional locksmith. They are quick, efficient and complete the task to a high standard.

It's not difficult to alter an upvc bar lock. You just need to know what is involved and follow the steps below.

Removing the Barrel Lock

uPVC doors and windows are popular in a variety of houses. They are great for allowing sunlight into your home and are easy to open with the correct key. Switching the barrel of a lock on a upvc door replacement lock (Suggested Browsing) door is an easy job that only takes five minutes. If you have lost your keys, a tenant left and has not returned them, or if the barrel of the lock is damaged and needs to be replaced, this is an easy solution.

You will need to remove the screws that hold the handles first. This is to get the handles removed from the way to access the barrel screw that locks them. Be careful not to loosen the screws too quickly as this could cause damage to the handles or cause them to fall off while working.

After the screws are removed, look for the screw that holds the barrel lock in position on the inside of your door. This screw stands out and is a different color to the other screws on the door. With the Phillips screwdriver, take out this screw. Next, take the present key that is used for the lock and put it into the barrel. Turn it to the right as far as you can. This will open the barrel and make it easier to open the door.

After loosening the screw, you can now break the pins that hold the Euro Cylinder in place. You will need pliers with strength or mole grips accomplish this. Take the protruding end of the euro cylindrical cylinder and bend it upwards and down and side to side. This will break the two support pins that are holding it in place.

Once the old cylinder has been taken out, you can then start the process of installing the new one. To ensure you order the correct replacement, you must first determine the cylinder's size. This can be done by measuring the distance from the center of the circular portion of the keyhole to the middle of the square spindle. The measurement must be taken from the upper hole of the spindle.

Change the Cylinder

The euro cylinder is the primary locking mechanism of the door made of upvc. It is easy to change and don't need an expert locksmith or handyman service. If your lock isn't protected by this security feature, you must replace it with one that has. They aren't expensive and could save money and inconvenience in the event that your locks are compromised.

To start you must open the door and stand in front of it, upvc door replacement lock so that you can easily reach the screw that holds the handle with your hand or a suitable tool. Let it loosen a bit, maybe just a quarter turn to start the process.

The cylinder will now be easily removed since the screw will no longer hold it in its place. Next, you'll need to determine the size of replacement cylinder that you require. There are approximately 25 different sizes. It is recommended to take the old cylinder along when you buy the new one so you are sure it will fit.

If you're not sure of the dimensions then take a measurement from the center of the screw hole to the end of the cylinder. You can only be sure that you're buying the right sized cylinders to fit your upvc door by measuring from the center of the screw hole to the end of the cylinder.

Insert the new cylinder into your door in the opposite direction you removed the old one. It could be difficult to align the lock cam, but this is usually just an issue of alignment and should come right eventually.

You will now need to screw the long screw for securing back into its place. After that, you can check that the cylinder is secured within the door. You can now attach the handle back to the door and then test it again. If all is good, the cylinder lock on your Upvc door has been replaced and you should have added a second layer of security to your home.

Changing the Handle

There are many reasons why a door knob or handle can become loose. It can be due either to wear and tear of the handle or the square spindle inside the handle. In this instance, the door handle needs to be replaced.

Firstly it is important to make sure the door is propped open and can't close when you are removing and replacing the handle. Then remove the screws from the inside surface of the plate using a screwdriver. This will remove your handle from the plate. Be careful not to loose the screws as they'll need to be re-screwed back into place later.

You can now take off the handles to gain access to the cylinder lock within the door. The cylinder lock is round or bulb-shaped and is only used in multi-point locks for upvc window locks and some aluminum doors. The procedure of changing the cylinder is the same as that of changing the handle, however, you'll have to remove the old cylinder from the door, and replace with a new one.

When selecting the replacement handle, it's important to consider the size. The handle must be the same size as the original, because it must fit the existing screws holding the handle in place. You can start by consulting the table of sizes that lists the most common sizes of replacement handle plates and their keyhole centers.

Consider upgrading your upvc door handles to a more secure standard, such as a Sold Secure SS301 set or 2* Kitemark security handles. This will increase the security of your house and make it easier to operate your door. The cost of these sets will be a bit more expensive, but the added peace of mind and added security is well worth it. You don't want to have to push the door handle continuously upwards and downwards to open and close it.

Modifying the Lock

The lock on your door upvc door replacement lock made of uPVC could be a weak point for burglars. You may want to upgrade your uPVC door to a multipoint window lock repair in order to ensure it is secure. This would include an open hook and deadbolts to ward off burglars. A professional locksmith can help you with this, however it is also possible to complete the job yourself. The process is quick and easy. You'll need a few simple tools.

The first step is to loosen the screws that hold in the handle. Using a screwdriver, you can take the screws off and place them in a safe place. Then, you can lift the handle to reveal the screw that holds the cylinder. You can remove this screw and replace it an alternative. Make sure that the screw is of the same size as the one you used before. It should be aligned properly with the barrel of lock.

The process of changing the lock on your uPVC door can be a challenge. You depend on it to safeguard your home, and making an error could cause you to be without a way to open the door. If you know how, it's quite simple and is less expensive than contacting a professional locksmith.

To change the lock on your uPVC door, you will have to open the inner faceplate of the lock. You'll need to locate the screw inside the door, and the retaining bolt outside the door. Once you have these screws in your hands, you are able to remove and replace the faceplate.

You may need to change the lock of your uPVC door for a variety of reasons. It could be due to a lost key, a tenant moved out and did not return the keys, or you simply want to increase the security of your home.

Anyone with a basic level of DIY skills can change the locking mechanism made of uPVC. If the lock replacement near me is stuck, you will need to check the hinges in the mechanism. If the hinges are greased, it should be an easy fix. If you aren't confident doing this, it is best to call an expert.